Subaru 2006 Baja Manuel d'utilisateur

ForewordCongratulations on choosing a SUBARU vehicle. This Owner’s Man-ual has all the information necessary to keep your SUBARU in excel-lent conditi

7– CONTINUED – Drinking and drivingDrinking and then driving is very dangerous.Alcohol in the bloodstream delays your reac-tion and impairs your perc

2-11Keys and doors– CONTINUED –2. Separate the case.3. Remove the old battery from the holder.1) Negative (–) side facing up4. Replace with a new batt

2-12Keys and doorsy Do not let dust, oil or water get on or in thetransmitter when replacing the battery.y Be careful not to damage the printed circui

2-13Keys and doors– CONTINUED –Transmitter circuit boardTo register a new transmitter with the keyless entrysystem, it is necessary to program the tra

2-14Keys and doors1) ON2) LOCK2)Insert the key into the ignition switch, then turn itfrom the “LOCK” position to the “ON” position 10times within 15 s

2-15Keys and doors– CONTINUED –times if the leftmost digit of the code is 8.NOTEy The electronic tone will stop sounding when youstart entering the nu

2-16Keys and doorswith the second digit (counting from the left) and finish-ing with the eighth digit. NOTEy When you finish entering the eighth digit

2-17Keys and doors– CONTINUED –once and the third one twice. This process will leaveonly current transmitter codes in the system’s memo-ry.NOTEMake su

2-18Keys and doorsseconds.The alarm is triggered by:y Opening a doory Turning the ignition switch to the “ON” positiony Physical impact to the vehicle

2-19Keys and doors– CONTINUED –: Press to Arm the system.: Press to Disarm the system.1) Security indicator light6. Briefly press the “ ” button (for

2-20Keys and doorstomatically arm and doors will automatically lock.T To arm the system using power door locking switches1. Close all windows.2. Remov

8 Driving when tired or sleepyWhen you are tired or sleepy, your reaction willbe delayed and your perception, judgment andattentiveness will be impai

2-21Keys and doors– CONTINUED – Disarming the systemDisarmi ng the systemBriefly press the “ ” button (for less than two sec-onds) on the remote tra

2-22Keys and doorsT Arming the system 1. Turn the ignition switch to the “ON” position.1) ON2) LOCK2. Turn the ignition switch from “ON” to “LOCK” pos

2-23Keys and doors– CONTINUED –In passive mode, the system will automaticallyactivate the alarm but WILL NOT automaticallylock the doors. In order to

2-24Keys and doorsbreaking the glass using a rescue hammer).y The shock sensors may sense vibration likethose shown in the following and trigger the a

2-25Keys and doors– CONTINUED –the doors from being opened even if the inside doorhandle is pulled.When the child safety lock lever is in the lock pos

2-26Keys and doorsT Driver’s side switches1) Lock switch2) For driver’s window3) For rear left passenger’s window4) For front passenger’s window5) For

2-27Keys and doors– CONTINUED –way, pull the switch up lightly.To close:Pull the switch up lightly and hold it. The window willclose as long as the sw

2-28Keys and doorsRear passenger’s window switches1) Open2) CloseTo open the window, push the switch down and hold ituntil the window reaches the desi

2-29Keys and doors– CONTINUED –upper surface of the rear bumper to avoid damagingthe tailgate.Vehicle without hard bed cover:To open the tailgate, lif

2-30Keys and doors1) Straps2) Cargo tie-down hooksIf you are going to drive with the optional SUBARUBed Extender installed, the rear section of the ha

9– CONTINUED –rier which can be secured to the rear seat by routing aseatbelt through the carrier’s handle. Never restrainpets or pet carriers in the

2-31Keys and doors– CONTINUED –To use the license plate bracket at its lowered/openposition, push the two release buttons and pull the li-cense plate

2-32Keys and doorsSwitchback doorSwitchback doorWith the switchback door open, you can increase theusable cargo space and can carry long objects.Secur

2-33Keys and doors– CONTINUED –1) RedA) LOCKB) UNLOCK2. Unlock the rear seatback by pulling up on the knoband fold down the rear seatback. Confirm tha

2-34Keys and doors3. Fold down the switchback door by releasing thelock knob. Then you can have a flat and larger cargospace. 4. Place the long object

2-35Keys and doors– CONTINUED –the vehicle body that prevent the door from ful-ly closing or that crimp the weather striparound the door.To close the

2-36Keys and doorsMoonroof (if equipped)MoonroofNever let anyone’s hands, arms, head or anyobjects protrude from the moonroof. A personcould be seriou

2-37Keys and doors– CONTINUED –roof is fully closed.Push the rear side of the “Tilt” switch to raise themoonroof. Push the front side of the “Tilt” sw

3-13Instruments and controlsIgnition switch ... 3-2LOCK ...

3-2Instruments and controlsInstrume nts and con trolsIgnition switchIgnition switchy Never turn the ignition switch to “LOCK”while the vehicle is bein

3-3Instruments and controls– CONTINUED –holder is attached to the key, your knees or handsmay accidentally touch it in a way that turns the ig-nition

3-4Instruments and controlsT Manual transmission vehiclesThe key can be turned from “ACC” to “LOCK” onlywhen the key is pushed in while turning it. A

3-5Instruments and controls– CONTINUED – Key interlock release (AT vehicles)Key Interlock releaseIf the key can not be turned to the “LOCK” positio

3-6Instruments and controlsHazard warning flasherHazard warning flasherThe hazard warning flasher is used to warn other driv-ers when you have to park

3-7Instruments and controls– CONTINUED –1) Trip meter2) OdometerT OdometerThe odometer shows the total distance that the vehiclehas been driven.T Doub

3-8Instruments and controlsmore than 1 second.NOTEIf the connection between the combination meterand battery is broken for any reason such as vehi-cle

3-9Instruments and controls– CONTINUED –The fuel gauge shows the approximate amount of fuelremaining in the tank.The gauge does not return to “E” even

3-10Instruments and controlsSee “In case of emergency” in chapter 9.1) Normal operating rangeThe temperature gauge shows engine coolant temper-ature w

3-11Instruments and controls– CONTINUED –Warning and indicator lightsWarning and i ndicator lightsSeveral of the warning and indicator lights come onm

3-12Instruments and controlstion.y Continuous illumination of the warning light.y Illumination of the warning light while driv-ing.When the ignition s

1491281234567131011Table of contentsSeat, seatbelt and SRS airbagsKeys and doorsInstruments and controlsClimate controlAudioInterior equipmentStarting

3-13Instruments and controls– CONTINUED –condition has been detected which may damage theemission control system.To prevent serious damage to the emis

3-14Instruments and controlsIf the light comes on while driving, it is unnecessary tostop the vehicle, but avoid driving up steep grades orin stop and

3-15Instruments and controls– CONTINUED –battery becomes fully charged, the light will go out. Brake system warning light Brake system  Warn ing

3-16Instruments and controls Low fuel warning light The low fuel warning light comes on when the tank isnearly empty approxima

3-17Instruments and controls– CONTINUED – Security system status indicator light (if equipped)This light is found at the bottom center of the combina

3-18Instruments and controls High beam indicator light High beam indicator light Indicator light High beamThis light shows that the

3-19Instruments and controls– CONTINUED –ClockClockTo set the time, turn the setting knob clockwise to ad-vance and counterclockwise to retard the tim

3-20Instruments and controls HeadlightsHeadlightsTo turn on the headlights, turn the knob on the end ofthe turn signal lever.first positionParking l

3-21Instruments and controls– CONTINUED – Headlight flasherHeadlight f lasherDo not hold the lever in the flashing position formore than just a few

3-22Instruments and controlsTurn signal leverTurn signal le ver1) Right turn2) Left turnTo activate the right turn signal, push the turn signal le-ver

12Illustrated index Exterior13 12 11 10 9 8123 5647UBF047BB1) Hood lock release knob (page 11-5)2) Headlight switch (page 3-20)3) Bulb replacement (p

3-23Instruments and controls– CONTINUED –Illumination brightness controlIllumination brig htness control1) Brighten2) DarkenWhen the lighting switch i

3-24Instruments and controlsthat will run down the battery.Front fog light buttonFront fog light buttonThe front fog lights operate only when the head

3-25Instruments and controls– CONTINUED –Wiper and washerWiper and washerIn freezing weather, do not use the windshieldwasher until the windshield is

3-26Instruments and controlsblades.NOTEy The wiper operates only when the ignitionswitch is in the “ON” or “ACC” position.y Clean your wiper blades an

3-27Instruments and controls– CONTINUED –To turn the wipers off, return the lever to the “OFF” po-sition.T Mist (for a single wipe)For a single wipe o

3-28Instruments and controlsRear window defogger buttonRear windowDefogger buttony Do not use sharp instruments or windowcleaner containing abrasives

3-29Instruments and controls– CONTINUED –Windshield wiper deicer (if equipped)WindshieldWiper deicerTo prevent the battery from being discharged,do no

3-30Instruments and controlsMirrorsMirrorsAlways check that the inside and outside mirrors areproperly adjusted before you start driving. Inside mirr

3-31Instruments and controls– CONTINUED –will illuminate.y By pressing and releasing the right button, the com-pass display is toggled on or off. When

3-32Instruments and controlsV Compass zone adjustment1. The zone setting is factory preset to Zone 8. Referto the “Compass calibration zone” map at th

13– CONTINUED –48512367UBF048BB1) Rear window defogger button (page 3-28)2) Fuel filler lid (page 7-4)3) Child safety locks (page 2-24)4) Towing hook

3-33Instruments and controls– CONTINUED –1) Selection switch2) Direction control switch1. Press either end of the selection switch, “L” for theleft, “

3-34Instruments and controlsThe indicator light located on the button will come onwhen the outside mirror defogger heater in operation.To turn it off,

3-35Instruments and controls– CONTINUED –place.5. Make sure that the steering wheel is securelylocked by moving it up and down.HornHornTo sound the ho

4-14Climate controlVentilator ... 4-2Driver’s side ventilators ...

4-2Climate controlClimate con trolVentilator Driver’s side ventilators1) Open2) CloseMove the thumb-wheel up and down or right and left toadjust the

4-3Climate control– CONTINUED – Front passenger’s side ventilators1) Open2) CloseMove the thumb-wheel up and down or right and left toadjust the flow

4-4Climate control Air flow selectionUB4036BA

4-5Climate control– CONTINUED –Manual heating and air conditioning system Control panel1) Temperature control dial2) Fan speed control dial3) Air flo

4-6Climate controlNOTEWhen the dial is placed in the “ ” or “ ” po-sition, the air conditioner compressor operatesautomatically regardless of the posi

14 InteriorT Passenger compartment area12543UBF065BB1) Lower anchorage for child re-straint system (page 2-24)2) Seatbelt (page 1-14)3) Parking brake

4-7Climate control– CONTINUED –ON position (Recirculation): Interior air is recirculat-ed inside the vehicle. Push the air inlet selection but-ton to

4-8Climate control“” position.T Heating and defrostingTo direct warm air toward the floor and the windshield:1. Set the air flow control dial to “ ”.2

4-9Climate control– CONTINUED –T Bi-level heatingThis setting allows you to direct air of different temper-atures from the instrument panel and foot o

4-10Climate controlContinued operation with the air inlet selectionbutton in the ON position may fog up the win-dows. Switch to the OFF position as so

4-11Climate control– CONTINUED –2. Set the temperature control dial to the red area.3. Set the fan speed control dial at the highest speed.Operating t

4-12Climate controlopen for a few minutes to allow outside air to circulateinto the heated interior. This results in quicker coolingby the air conditi

4-13Climate control– CONTINUED –Air filtration system (if equipped)If your vehicle’s air conditioning system is equippedwith a optional air filtration

5-15AudioAntenna system ... 5-2Pillar mounted antenna (Non-turbo models) .. 5-2Roof mounted antenna (Turbo m

5-2AudioAudioAntenna system Pillar mounted antenna (Non-turbo models)Pull the antenna out to extend it to its full length. Roof mounted antenna (Tur

15– CONTINUED –1254 3UBF050BB1) Moonroof (page 2-36)2) Interior lights (page 6-2)3) Sun visors (page 6-3)4) Map light (page 6-3)5) Inside mirror (page

5-3Audio– CONTINUED –Stand the roof antenna up for use. You can detach theroof antenna by turning it counterclockwise. When fit-ting the roof antenna,

5-4AudioInstallation of accessoriesAlways consult your SUBARU dealer before installinga citizen band radio or other transmitting device inyour vehicle

5-5Audio– CONTINUED – Type B audio sety Radio operation: refer to page 5-17 y Built-in CD changer operation: refer to page 5-23  In-dash 6 CD auto c

5-6AudioAM/FM radio with CD playerThe audio set will operate only when the ignition switch is in the “ACC” or“ON” position. Radio operation(1) (2)(6)

5-7Audio– CONTINUED –T Power switch and volume/bass/treble/fader/balance controlV Power switch and volume control (PWR/VOL)The dial (1) is used for bo

5-8AudioDisplay Control modeTurn counterclockwise Turn clockwiseBAS Bass control For less bass sound For more bass soundTRE Treble control For less tr

5-9Audio– CONTINUED –T Waveband selectionV FM/AM selectionPush the “BAND” button (2) to select FM1, FM2 or AMreception. The display indicates which on

5-10Audioseconds to store the frequency. At this time, there willmomentarily be no sound from the radio. If the buttonis pressed for less than 2 secon

5-11Audio– CONTINUED – Compact disc player operation(8)(7) (9)(14) (15) (13) (12) (11)(10)UB5067CB(7) Disc slot(8) CD button(9) Eject button(10) Fast

5-12AudioT To playback a compact discV When CD is not in the playerHold a disc with a finger in the center hole while grip-ping the edge of the disc,

1617321564UBF066BB1) Cup holder (page 6-7)2) Center console (page 6-5)3) Glove box (page 6-5)4) Cigarette lighter (page 6-9)5) Ashtray (page 6-12)6) A

5-13Audio– CONTINUED –V Fast-reversing Press the “ ” side of the button (11) continuouslyto fast-reverse the disc.Release the button to stop fast-reve

5-14Audio(16)(20) (19) (18) (17)UB5067DB(16) CD button(17) Track selection buttons(18) RAND (Random) button(19) RPT (Repeat) button(20) SCAN button

5-15Audio– CONTINUED –T To start playbackPress the “CD” button (16). The “CD” indicator willcome on and the disc number will appear on the dis-play an

5-16Audio– The display shows “SCAN” and the track numberbeing scanned.– You hear the first 10 seconds of each track.– The operation is automatically c

5-17Audio– CONTINUED –Type B audio set (if equipped)The radio will operate only when the ignition switch is in the “ACC” or “ON”position. Radio opera

5-18AudioT Power switch and volume/bass/treble/fader/balance control (PWR/VOL)The dial (1) is used for both power (ON/OFF) and vol-ume control. The ra

5-19Audio– CONTINUED –Display Control modeTurn counterclockwise Turn clockwiseBASS Bass control For less bass sound For more bass soundMIDDLE Midrange

5-20AudioV Tone controlThe volume control dial (1) normally function as vol-ume control. The dial become a control for Bass,Midrange or Treble when yo

5-21Audio– CONTINUED –V AM buttonPress the “AM” button (5) for AM reception.T Stereo indicatorThe stereo indicator “ST” will come on when an FMstereo

5-22Audiobutton is pressed for less than 1.5 seconds, the pre-ceding selection will remain in memory.NOTEy If the connection between the radio and bat

UBF046AA

17– CONTINUED –T Cargo bed/spare tire/jack124365UBF067BB1) Cargo lamp (page 6-20)2) Cargo tie-down hooks (page 6-17)3) Temporary spare tire (page 9-10

5-23Audio– CONTINUED – Built-in CD changer operation(9) (10) (11) (12)(15)(16)(17)(13) (14)UB5072CB(9) Eject button(10) Disc slot(11) CD (CD player s

5-24AudioNOTEMake sure to always insert a disc with the labelside up. If a disc is inserted with the label sidedown, it might be ejected or the player

5-25Audio– CONTINUED –enter standby mode. Press the “CD” button to startplayback.V Loading all the magazine (Full disc loading mode)1. If you continue

5-26AudioRelease the button to stop fast-reversing.T Repeat playbackPress the “RPT” button (12) while a song is playing toplay the song repeatedly. Th

5-27Audio– CONTINUED –In-dash 6 CD auto changer (if equipped)(1)(2)(3)(4)HS5016BB(1) Disc slot(2) Disc indicators (disc No.1 to 6)(3) Disc select butt

5-28Audioy Do not attempt to insert two or more discsinto the slot at a time. Doing so can cause me-chanical damage to the CD changer.y Use only music

5-29Audio– CONTINUED –2. Press the “Eject” button (4). The selected disc willbe ejected and the indicator light will begin blinking.3. To remove anoth

5-30AudioPrecautions to observe when han-dling a compact discUse only compact discs (CDs) that have the markshown in the following illustration. CD-RW

5-31Audio– CONTINUED –poor tone quality. Do not touch the disc surface. y Use a clean disc whenever possible. If there are de-posits, wipe the disc su

18 Instrument panel12 3 4 5 67891011121314151617UBF021BB1) Door locks (page 2-3)2) Outside mirror (page 3-32)3) Light control lever (page 3-19)4) Com

6-16Interior and exterior equipmentsInterior light ... 6-2Dome light ...

6-2Interior and exterior equipmentsInterior and exterior equipmentsInterior light Dome lightThe dome light switch has three positions:ON: The light s

6-3Interior and exterior equipments– CONTINUED –Map light1) Switches2) Map lightsTo turn on the map light, push the switch. To turn it off,push the sw

6-4Interior and exterior equipments Vanity mirror (if equipped)To use the vanity mirror, swing down the sun visor andopen the vanity mirror cover.The

6-5Interior and exterior equipments– CONTINUED – Glove box1) Lock2) UnlockTo open the glove box, pull the handle. To close it,push the lid firmly upw

6-6Interior and exterior equipments Rear center consoleTo open the lid, push the button. Coin compartmentTo open the coin compartment, pull the uppe

6-7Interior and exterior equipments– CONTINUED –Cup holdery Do not pick up a cup from the cup holder orput a cup in the holder while you are driving,

6-8Interior and exterior equipments Rear passenger’s cup holderA dual cup holder is built in the rear center console.Accessory power outletThe access

6-9Interior and exterior equipments– CONTINUED –y Do not place any foreign objects, especiallymetal ones such as coins or aluminum foil, intothe acces

6-10Interior and exterior equipmentsThe electrical power socket located on the lower partof the instrument panel can be used as cigarette light-er soc

19– CONTINUED – Light control and wiper control levers/switches1234576891011UBF023DB1) Parking light switch (page 3-23)2) Windshield wiper (page 3-25

6-11Interior and exterior equipments– CONTINUED – Using as an accessory power outletElectrical power (12V DC) from the battery is availableat the soc

6-12Interior and exterior equipmentsAshtrayDo not use ashtrays as waste receptacles orleave a lighted cigarette in an ashtray. Thiscould cause a fire.

6-13Interior and exterior equipments– CONTINUED –Convenience hook Coat hookNever hang anything on the coat hook thatmight obstruct the driver’s view

6-14Interior and exterior equipmentsThere are four hooks on the back panel behind therear seatback.These hooks can be used for installing a cargo net

6-15Interior and exterior equipments– CONTINUED –Floor mat (if equipped)Make sure the driver’s floor mat is placed backin its proper location and corr

6-16Interior and exterior equipmentsCargo bedy Never fill gasoline containers on the cargobed. Static electricity may ignite gasoline vaporwhen fillin

6-17Interior and exterior equipments– CONTINUED –front end of the cargo bed. Keep those holes clear andfree from obstructions. Cargo tie-down hooksTh

6-18Interior and exterior equipmentsy Remove the bed extender for vehicle “OffRoad” use.y To avoid creating a dangerous road hazard orcausing personal

6-19Interior and exterior equipments– CONTINUED –NOTEUse care when rotating bed extender. Do not per-mit the buckles to come in contact with vehiclesh

6-20Interior and exterior equipmentsCargo lampThe cargo lamp comes on and goes off whenever thecargo lamp switch is pushed regardless of the positiono

20 Combination meterT Non-turbo models12 3 456789UBF063BB1) Fuel gauge (page 3-8)2) Speedometer (page 3-6)3) Tachometer (page 3-8)4) Temperature gaug

6-21Interior and exterior equipments– CONTINUED –Soft bed cover (if equipped)Before installing the soft bed cover, carefullyread the warning labels on

6-22Interior and exterior equipmentsTo secure the soft portion of the bed cover to the bed,simply start from either side of the vehicle and placethe p

6-23Interior and exterior equipments– CONTINUED –The soft portion of the bed cover can be removed fromthe bed cover’s hard section for cleaning or sto

6-24Interior and exterior equipmentsHard bed cover (if equipped)1) Warning labelsy Carefully read the warning labels on the in-side walls of the cargo

6-25Interior and exterior equipments– CONTINUED –1) Front section2) Rear sectionThe hard bed cover can be used to cover the entirecargo area. Its fron

6-26Interior and exterior equipmentsThe front and rear sections of the bed cover can eachbe locked and unlocked. Each section is automaticallylocked w

6-27Interior and exterior equipments– CONTINUED –NOTEIf you find the key hard to turn when unlocking therear section, press the middle of the rear sec

6-28Interior and exterior equipments1) Internal hard bed cover release handleTo open the hard bed cover from inside the cargo bed,turn the yellow hand

6-29Interior and exterior equipments– CONTINUED –bars with the attached strap. Failure to do somay result in damage to cargo.y When opening or closing

6-30Interior and exterior equipments2. Raise the cover slightly while holding the key in theunlock position. After making sure that the cover iscomple

21– CONTINUED –T Turbo models12 435678910UBF064BB1) Fuel gauge (page 3-8)2) Speedometer (page 3-6)3) Gear position indicator (page 3-17)4) Tachometer

6-31Interior and exterior equipments– CONTINUED –1) Straps 1) Rear section of cover2) Rear sport bar3) Strap4) Connector3. Take the strap from the bac

6-32Interior and exterior equipmentsly locked.If this does not lock the cover, release it from a slightlyhigher position. Do not push the cover forcib

6-33Interior and exterior equipments– CONTINUED –1) Bolts3. Remove the two bolts shown in the above drawingusing the wheel nut wrench.1UB6069BAUB6070B

6-34Interior and exterior equipments4. Fold up the front and rear sections of the cover. Re-move the cover by holding it (by two or more adults)and pl

6-35Interior and exterior equipments– CONTINUED –3. Tighten the two bolts shown in the above drawingby hand and confirm that the hard bed cover is mou

6-36Interior and exterior equipmentsRoof rail and crossbary For cargo carrying purposes, the roof railmust be used together with a roof crossbar kitan

6-37Interior and exterior equipments– CONTINUED –formation on loading cargo into or onto your vehicle.The maximum load limit of the cargo, crossbars a

6-38Interior and exterior equipmentsT To remove the crossbar 1. Loosen and remove the T-30 torx® head screwfrom the side of each crossbar end support.

6-39Interior and exterior equipments– CONTINUED –1) Front2) Rear3) Crossbar (section)Front crossbar:Front crossbar has 100 LBS. Load Label on left han

6-40Interior and exterior equipments1. Before placing the crossbar on the roof rails, makesure that the T-30 torx® head screw is fully loosenedfrom ea

22T Warning and indicator lightMark Name PageSeatbelt warning light 3-11SRS airbag system warning light3-11CHECK ENGINE warning light/Malfunction indi

6-41Interior and exterior equipments– CONTINUED –vided).Rear crossbar:Install the rear crossbar in the same manner as thefront crossbar.NOTEy The rear

6-42Interior and exterior equipmentsSport activity lights (if equipped)1) Indicator lightThe sport activity lights will operate only when theparking b

6-43Interior and exterior equipments– CONTINUED –(downward) position when washing your vehicle. If you choose to remove sport activity lights, the fol

7-17Starting and operatingFuel ... 7-2Fuel requirements ...

7-2Starting and operatingStarting and ope ratingFuelUse of a fuel which is low in quality or use of aninappropriate fuel additive may cause enginedama

7-3Starting and operating– CONTINUED –California is permitted to have higher sulfur levels,which may affect the performance of your vehicle’scatalytic

7-4Starting and operatingitors required to prevent damage to the fuel system.Do not use fuel containing methanol EXCEPT underthese conditions.y If und

7-5Starting and operating– CONTINUED –01. To open the fuel filler door, pull it outward.1) Open2) Close2. Remove the fuel filler cap by turning it slo

7-6Starting and operatingNOTEy You will see the “FUEL DOOR ” sign in thetachometer. This indicates that the fuel filler door(lid) is located on the ri

1-11Seat, seatbelt and SRS airbagsFront seats ... 1-2Fore and aft adjustment ...

7-7Starting and operating– CONTINUED –obligation under federal law to implement stricter vehi-cle emission standards to reduce air pollution from ve-h

7-8Starting and operatingy A state emission inspection may reject (not pass orfail) a vehicle if the number of OBD system readinessmonitors “Not Ready

7-9Starting and operating– CONTINUED –Starting the engineDo not operate the starter motor continuouslyfor more than ten seconds. If the engine fails t

7-10Starting and operatingtery has been disconnected and reconnected (formaintenance or other purposes). This difficulty iscaused by the electronicall

7-11Starting and operating– CONTINUED –While the engine is warming up, make sure that theselector lever is at the “P” or “N” position and that thepark

7-12Starting and operatingManual transmissionDo not drive the vehicle with the clutch disen-gaged (i.e., when the clutch pedal is depressed)or with th

7-13Starting and operating– CONTINUED – Shifting speedsT Recommended shifting speedsThe best compromise between fuel economy and ve-hicle performance

7-14Starting and operating Driving tipsDo not drive with your foot resting on the clutch pedaland do not use the clutch to hold your vehicle at astan

7-15Starting and operating– CONTINUED –y When parking the vehicle, first securely applythe parking brake and then place the selectorlever in the “P” p

7-16Starting and operating: With the brake pedal depressed, move the lever along the gate.: Move the lever along the gate.The selector lever has seven

1-2Seat, seatbelt and SRS airbagsSeat, seat belt and SRS airba gsFront seatsy Never adjust the seat while driving to avoidthe possibility of loss of v

7-17Starting and operating– CONTINUED –In this position the wheels and transmission are notlocked. In this position, the transmission is neutral; thev

7-18Starting and operatingT 3 (Third)This position is for using engine braking when goingdown a hill or for climbing a grade.The transmission automati

7-19Starting and operating– CONTINUED –mph (km/h)Never exceed posted speed limits.NOTEy In order to prevent over-revving during acceler-ation of the v

7-20Starting and operating4. Insert the screwdriver into the hole.5. Push down on the screwdriver and move the selec-tor lever from the “P” to the “N”

7-21Starting and operating– CONTINUED –Automatic transmission (Turbo mod-els)Do not shift from the “P” or “N” position intothe “D”, “3”, “2”, “1” or “

7-22Starting and operatingas the vehicle continues to be driven for a while. Selector lever1) Release button: With the brake pedal depressed, shift w

7-23Starting and operating– CONTINUED –locked to prevent the vehicle from rolling freely.When you park the vehicle, first set the parking brakefully,

7-24Starting and operatingThe transmission automatically shifts into a suitablegear from 1st to 4th according to the vehicle speedand the acceleration

7-25Starting and operating– CONTINUED –that position. The transmission will automaticallydownshift to 2nd or 1st gear. When you release thepedal, the

7-26Starting and operatingT Selector lever release buttonIf you inadvertently have turned the ignition switch tothe “OFF” position with the selector l

1-3Seat, seatbelt and SRS airbags– CONTINUED –restrained or improperly restrained. Becausechildren are lighter and weaker than adults,their risk of be

7-27Starting and operating– CONTINUED –1) Lamp showing whether upshift is possible2) Lamp showing whether downshift is possible3) Indication of curren

7-28Starting and operatingmatic transmission from damage.y The transmission does not automatically shiftup in the SPORTSHIFT mode. Perform gearshiftsi

7-29Starting and operating– CONTINUED –Never exceed posted speed limits.NOTEy In order to prevent over-revving during acceler-ation of the vehicle, th

7-30Starting and operating4. Insert the screwdriver into the hole.5. Push down on the screwdriver, push down the but-ton and move the selector lever f

7-31Starting and operating– CONTINUED –Power steeringDo not hold the steering wheel at the fullylocked position left or right for more than fivesecond

7-32Starting and operatingT Braking when a tire is puncturedDo not depress the brake pedal suddenly when a tireis punctured. This could cause a loss o

7-33Starting and operating– CONTINUED –ABS (Anti-lock Brake System)Always use the utmost care in driving – over-confidence because you are driving wit

7-34Starting and operating ABS warning lightThe ABS warning light comes on when the ignitionswitch is turned to the “ON” position and goes out aftera

7-35Starting and operating– CONTINUED –age and does not indicate a malfunction. When thebattery becomes fully charged, the light will go out.Parking y

7-36Starting and operatingmake sure that the parking brake has been fullyreleased.To set the parking brake, press the brake pedal firmlyand hold it do

1-4Seat, seatbelt and SRS airbagsT Manual typePull the lever upward and slide the seat to the desiredposition. Then release the lever and move the sea

7-37Starting and operating– CONTINUED –When facing downhill, the front wheels should beturned into the curb.Cruise controlDo not use the cruise contro

7-38Starting and operating To set cruise control01. Push the “CRUISE” main switch. The indicator lighton the switch will come on.2. Depress the accel

7-39Starting and operating– CONTINUED –When the accelerator pedal is released, the vehiclewill return to and maintain the previous cruising speed. To

7-40Starting and operatingdepressing the accelerator pedal.NOTEIf the difference between the actual vehicle speedwhen the control lever is pushed down

8-18Driving tipsNew vehicle break-in driving – the first 1,000 miles (1,600 km) ... 8-2Fuel economy hints ...

8-2Driving tipsDriving tipsNew vehicle break-in driving – the first 1,000 miles (1,600 km)The performance and long life of your vehicle are de-pendent

8-3Driving tips– CONTINUED –Engine exhaust gas (Carbon monox-ide)y Never inhale engine exhaust gas. Engine ex-haust gas contains carbon monoxide, a co

8-4Driving tipsCatalytic convertery Avoid fire hazards. Do not drive or park thevehicle anywhere near flammable materials(e.g. grass, paper, rags or l

8-5Driving tips– CONTINUED –Turbo modelsThe catalytic converter is installed in the exhaust sys-tem. It serves as catalyst to reduce HC, CO and NOxin

8-6Driving tipsPeriodic inspectionsTo keep your vehicle in the best condition at all times,always have the recommended maintenance serviceslisted in t

1-5Seat, seatbelt and SRS airbags– CONTINUED –To adjust the angle and height of the seat cushion,move the control switch in the corresponding directio

8-7Driving tips– CONTINUED –Driving tips for AWD vehiclesy Always maintain a safe driving speed accord-ing to the road and weather conditions in order

8-8Driving tipsy An AWD vehicle is better able to climb steeperroads under snowy or slippery conditions than a twowheel drive vehicle. There is little

8-9Driving tips– CONTINUED –Off road drivingy Always maintain a safe driving speed accord-ing to the road and weather conditions in orderto avoid havi

8-10Driving tipsless of its depth, it can wash away the ground from un-der your tires, resulting in possible loss of traction andeven vehicle rollover

8-11Driving tips– CONTINUED –y Frequent driving of an AWD vehicle under hard-driv-ing conditions such as rough roads or off roads will ne-cessitate mo

8-12Driving tipsstarting.Keep the door locks from freezing by squirting themwith deicer or glycerin.Forcing a frozen door open may damage or separatet

8-13Driving tips– CONTINUED –severe winter driving, stop when and where it is safeto do so and check under the fenders periodically.T Parking in cold

8-14Driving tipsAvoid prolonged continuous driving in snow-storms. Snow will enter the engine’s intake sys-tem and may hinder the air flow, which coul

8-15Driving tips– CONTINUED –give superior wiping performance in snowy conditions.Be sure to use blades that are suitable for your vehi-cle.During hig

8-16Driving tipsstall four winter tires that are of the same size, con-struction, brand and load range and you should nevermix radial, belted bias or

1-6Seat, seatbelt and SRS airbagsTo prevent the passenger from sliding underthe seatbelt in the event of a collision, alwaysput the seatback in the up

8-17Driving tips– CONTINUED –When the road surface is extremely slippery, you canobtain better traction by starting the vehicle with thetransmission i

8-18Driving tipsevent of a sudden stop or accident. Keep lug-gage or cargo low, as close to the floor as pos-sible.y When you carry something inside t

8-19Driving tips– CONTINUED – Vehicle capacity weightThe load capacity of your vehicle is determined byweight, not by available cargo space. The maxi

8-20Driving tipsdoor shows GVWR (Gross Vehicle Weight Rating)and GAWR (Gross Axle Weight Rating).The GVW (Gross Vehicle Weight) must never exceedthe G

8-21Driving tips– CONTINUED –tributing hitch.The trailer hitch is designed to tow a Class 1 ratedload. A maximum of 2,400 lbs (1,087 kg) gross trailer

8-22Driving tips3. Insert the hitch pin into the hole on the hitch receiv-er tube so that the pin passes through the ball mount.4. Insert the safety p

8-23Driving tips– CONTINUED –1) Hitch ball installation point2) Hooks for safety chains6. Use only a hitch ball that is appropriate for the ballmount

8-24Driving tipsHitch harness connector9. Connect the hitch wire harness’s black four-pinwire connector to the towing trailer’s wire harness.10.Confir

8-25Driving tips– CONTINUED –Trailer towingYour vehicle is designed and intended to be used pri-marily to carry passengers and cargo. Towing a trailer

8-26Driving tipsand trailer are acceptable.T Total trailer weightTotal trailer weightThe total trailer weight (trailer weight plus its cargoload) must

1-7Seat, seatbelt and SRS airbags– CONTINUED –the vehicle is struck from the rear. Lumbar support (if equipped)Pull the lever forward or backward.Pul

8-27Driving tips– CONTINUED –T Gross Vehicle Weight (GVW) and Gross Vehicle Weight Rating (GVWR)Gross Vehicle WeightThe Gross Vehicle Weight (GVW) mus

8-28Driving tipsT Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR)Gross Axle WeightThe total weight applied to each axle (GAW) must nev-er

8-29Driving tips– CONTINUED –T Tongue loadTongue loadIf the trailer is loaded with more weight in theback of trailer’s axle than in the front, the loa

8-30Driving tipsF: FrontThe tongue load can be adjusted by proper distributionof the load in the trailer. Never load the trailer withmore weight in th

8-31Driving tips– CONTINUED –mended. A genuine SUBARU hitch is available fromyour SUBARU dealer.If use of a non-genuine hitch is unavoidable, be suret

8-32Driving tipsloose and create a traffic safety hazard.For safety, always connect the towing vehicle andtrailer with trailer safety chains. Pass the

8-33Driving tips– CONTINUED –tire is used. The temporary spare tire is not de-signed to sustain the towing load. Use of thetemporary spare tire when t

8-34Driving tips– the trailer tongue is connected properly to thehitch ball.– the trailer lights connector is connected properlyand trailer’s brake li

8-35Driving tips– CONTINUED –y Backing up with a trailer is difficult and takes prac-tice. When backing up with a trailer, never accelerateor steer ra

8-36Driving tipsvehicle and trailer wheels.3. When the wheel blocks are in place, release theregular brakes slowly until the blocks absorb the load.4.

1-8Seat, seatbelt and SRS airbags1) Indicator lightTo turn on the seat heater, push the “LO” or “HI” posi-tion on the switch, as desired, depending on

9-19In case of emergencyIf you park your vehicle in an emergency .. 9-2Jack and tools ... 9-3Location of

9-2In case of emergencyIn case o f emergencyIf you park your vehicle in an emer-gencyThe hazard warning flasher should be used in day ornight to warn

9-3In case of emergency– CONTINUED –Jack and toolsThe jack supplied with the vehicle is designed only forchanging a tire.Before using the jack, see th

9-4In case of emergency01) RedA) LOCKB) UNLOCK1. Pull the rear seatback locks up and fold down therear seatback to gain access to the rear quarter poc

9-5In case of emergency– CONTINUED –4. Loosen the jack holding screw by turning counter-clockwise and remove the jack from the pocket.NOTEy Be careful

9-6In case of emergency3. Place the jack onto the bracket in the pocket.4. Securely fix the jack with the jack holding screw byturning it clockwise.5.

9-7In case of emergency– CONTINUED –Spare tireThe spare tire is stored in the spare tire holder locatedunder the rear of the cargo bed.The spare tire

9-8In case of emergency4. Turn the hoist shaft end counterclockwise with thewheel nut wrench until the temporary spare tire is onthe ground with enoug

9-9In case of emergency– CONTINUED –underside of the vehicle. Driving with the cablenot retracted fully could result in damage to theadjacent under fl

9-10In case of emergencyTemporary spare tire Using the temporary spare tireNever tow a trailer when the temporary sparetire is used. The temporary sp

1-9Seat, seatbelt and SRS airbags– CONTINUED –Rear seatsy Seatbelts provide maximum restraint whenthe occupant sits well back and upright in theseat.

9-11In case of emergency– CONTINUED –1) Tread wear indicator bar2) Indicator location marky When the wear indicator appears on the tread, re-place the

9-12In case of emergencyFlat tiresIf you get a flat tire while driving, never brake sudden-ly; keep driving straight ahead while gradually reduc-ing s

9-13In case of emergency– CONTINUED –agonally opposite the flat tire.5. Take out the spare tire, jack, and wheel nut wrench.Refer to the sections “Spa

9-14In case of emergencyindicated by arrow marks on the side of the side sillskirt.3. Turn the jackscrew by hand until the groove of thejack head enga

9-15In case of emergency– CONTINUED –6. Before putting the spare tire on, clean the mountingsurface of the wheel and hub with a cloth.7. Put on the sp

9-16In case of emergency9. Use the wheel nut wrench to securely tighten thewheel nuts to the specified torque, following the tight-ening order in the

9-17In case of emergency– CONTINUED –1) Holding rod2) Retainer3. Place the flat tire in the cargo bed with the outerside of the wheel facing up. For a

9-18In case of emergencytions and precautions described in the “Temporaryspare tire” section in this chapter.Replace the temporary spare tire with a c

9-19In case of emergency– CONTINUED –Do not jump start unless cables in suitable con-dition are available.y A running engine can be dangerous. Keepyou

9-20In case of emergency1) Booster battery2) Engine lifting bracket__++4123129002751)Connect one jumper cable to thepositive (+) terminal on the dis-c

1-10Seat, seatbelt and SRS airbags Folding down the rear seaty After returning the rear seat to its original po-sition, be certain to place all of th

9-21In case of emergency– CONTINUED –5. Start the engine of the vehicle with the booster bat-tery and run it at moderate speed. Then start the en-gine

9-22In case of emergencyConfirm that the cooling fan is turning. If the fan is notturning, immediately turn off the engine and contactyour authorized

9-23In case of emergency– CONTINUED –dealer or a commercial towing service. Observe thefollowing procedures for safety. Towing and tie-down hooksThe

9-24In case of emergency1) Tie-down hook 1) Tie-down hook2) Towing and tie-down hook1UB9070BB21UB9066CB

9-25In case of emergency– CONTINUED –Vehicle with trailer hitch (if equipped)1) Tie-down hookT Towing hook cover removal procedureThe towing hook cove

9-26In case of emergency2. Pull off the towing hook cover.T Towing hook cover installation procedureTo reinstall the towing hook cover, push it in on

9-27In case of emergency– CONTINUED – Using a flat-bed truckThis is the best way to transport your vehicle. Use thefollowing procedures to ensure saf

9-28In case of emergencyy If transmission failure occurs, transport yourvehicle on a flat-bed truck.y Do not run the engine while the vehicle is be-in

10-110Appearance careExterior care ... 10-2Washing ...

10-2Appearance careAppearan ce careExterior care Washingy When washing the vehicle, the brakes mayget wet. As a result, the brake stopping dis-tance

1-11Seat, seatbelt and SRS airbags– CONTINUED –T Folding down the seatbackBefore folding down the seatback, check thatthere is nothing in the seatback

10-3Appearance care– CONTINUED –After driving off-road or muddy or sandy roads, washthe mud and sand off the underbody.Carefully flush the suspension

10-4Appearance care Cleaning aluminum wheelsy Promptly wipe the aluminum wheels clean of anykind of grime or agent. If dirt is left on too long, it m

10-5Appearance care– CONTINUED –Corrosion protectionYour SUBARU has been designed and built to resistcorrosion. Special materials and protective finis

10-6Appearance carecumulation under the floor mats because that couldcause corrosion. Occasionally check under the matsto make sure the area is dry.Ke

10-7Appearance care– CONTINUED – Leather seat materialsThe leather used by SUBARU is a high quality naturalproduct which will retain its distinctive

11-111Maintenance and serviceMaintenance schedule ... 11-3Maintenance precautions ... 11-3Bef

11-2Maintenance and serviceTypes of tires ... 11-46Tire inspection ...

11-3Maintenance and service– CONTINUED –Maintenance a nd serviceMaintenance scheduleMaintenanceScheduleThe scheduled maintenance items required to be

11-4Maintenance and servicethe materials in the vehicle may be hazardous ifimproperly used or handled, for example, bat-tery acid.y Your vehicle shoul

1-12Seat, seatbelt and SRS airbagsT Folding down the seat cushion and seatbackBefore folding down the seatback, check thatthere is nothing in the seat

11-5Maintenance and service– CONTINUED –even when the engine is stopped. When you do checking or servicing in the engine compartment while the en-gin

11-6Maintenance and service3. Release the secondary hood release located underthe front grille by moving the lever toward the left.4. Lift up the hood

11-7Maintenance and service– CONTINUED –it. It could deform the metal.Always check that the hood is properly lockedbefore you start driving. If it is

11-8Maintenance and serviceEngine compartment overviewEngineCompartm ent overvi ew Non-turbo models12 345678910111213UBB106BB1) Manual transmission o

11-9Maintenance and service– CONTINUED – Turbo models111 10 9 81213234567UBB098CB1) Air cleaner element (page 11-23)2) Manual transmission oil level

11-10Maintenance and serviceEngine oilEngineOilOil levelEngine Checking the oil levelChecking Engine oil levelCheck the engine oil level at each fu

11-11Maintenance and service– CONTINUED –Non-turbo models1) Notch2) Upper level3) Lower levelTurbo models1) Notch2) Upper level3) Lower level4. Pull o

11-12Maintenance and servicea bad smell, smoke, and/or a fire. If engine oilgets on the exhaust pipe, be sure to wipe it off.If you check the oil leve

11-13Maintenance and service– CONTINUED –oil.1) Sealing washer2) Drain plug5. Wipe the seating surface of the drain plug with aclean cloth and tighten

11-14Maintenance and service7. Slide the cover toward the vehicle front to removeit.8. Remove the oil filter with an oil filter wrench.9. Before insta

1-13Seat, seatbelt and SRS airbags– CONTINUED –A) LOCKB) UNLOCK1) Red4. Unlock the seatback by pulling the release knob upand fold the seatback down.

11-15Maintenance and service– CONTINUED –Oil capacity (Guideline):4.2 US qt (4.0 liters, 3.5 Imp qt)The oil quantity indicated above is only a guideli

11-16Maintenance and serviceAPI Service label1) Indicates the oil quality by API designations2) Indicates the SAE oil viscosity grade3) Indicates that

11-17Maintenance and service– CONTINUED –API classification SM (or SL):SAE viscosity No.:30, 40, 10W-50, 20W-40, 20W-50Cooling systemCooling systemNev

11-18Maintenance and serviceed parts. The alcohol contained in the enginecoolant may damage the paint surface. Hose and connectionsHose and connecti

11-19Maintenance and service– CONTINUED –1) Rubber gaskets3. After refilling the reserve tank and the radiator, re-install the caps and check that the

11-20Maintenance and serviceTurbo models2. Place a proper container under the drain plug andloosen the drain plug.Never attempt to remove the radiator

11-21Maintenance and service– CONTINUED –Turbo models1) Filler neck2) Fill up to here4. Slowly pour the coolant and fill up to just below thefiller ne

11-22Maintenance and service1) “FULL” level mark2) “LOW” level mark5. Pour the coolant and fill to the reservoir tank’s“FULL” level mark.1) Rubber gas

11-23Maintenance and service– CONTINUED –Air cleaner elementAir clea ner elemen tDo not operate the engine with the air cleanerelement removed. The ai

11-24Maintenance and service1) Air cleaner element3. Separate the rear air cleaner element case fromthe front air cleaner element case and remove the

1-14Seat, seatbelt and SRS airbagsplace and make sure that they are securely locked. Make sure that the rear seatbelt buckles are not underthe seat cu

11-25Maintenance and service– CONTINUED –1) Air cleaner case cover2) Air cleaner element2. Open the air cleaner case cover and remove the aircleaner e

11-26Maintenance and serviceThe spark plugs should be replaced according to themaintenance schedule in the “Warranty and Mainte-nance Booklet”. Recom

11-27Maintenance and service– CONTINUED –in (mm)To check belt tension, place a straightedge (ruler)across two adjacent pulleys and apply a force of 22

11-28Maintenance and serviceTurbo models1. Park the vehicle on a level surface and stop the en-gine.2. Pull out the dipstick, wipe it clean, and inser

11-29Maintenance and service– CONTINUED – Recommended grade and viscosityRecommended Oil grade and viscosityEach oil manufacturer has its own base

11-30Maintenance and service1) Yellow handle1) Yellow handle1UBB004KBHSB018MB1

11-31Maintenance and service– CONTINUED –A) HOT rangeB) COLD range1) Upper level2) Lower level4. Pull out the dipstick and check the fluid level on th

11-32Maintenance and serviceFront differential gear oil (AT vehi-cles)Differential g ear oilFrontFrontDifferen tial gear oilOil levelFront differentia

11-33Maintenance and service– CONTINUED – Recommended grade and viscosityRecommended Oil grade and viscosityEach oil manufacturer has its own base

11-34Maintenance and serviceNon-turbo AT1) Filler plug2) Drain plug1) Filler hole2) Drain hole3) Oil level12OM-U0213123OM-U0214

1– CONTINUED –Warranties Warranties for U.S.A.All SUBARU vehicles distributed by Subaru of Ameri-ca, Inc. and sold at retail by an authorized SUBARUd

1-15Seat, seatbelt and SRS airbags– CONTINUED –cially if they are 12 years of age and under andare not restrained or improperly restrained. Be-cause c

11-35Maintenance and service– CONTINUED –Others1) Filler plug2) Drain plug1) Filler hole2) Drain hole3) Oil levelRemove the plug from the filler hole

11-36Maintenance and serviceOil grade:API classification GL-5SAE viscosity No. and applicable temperaturePower steering fluidPowerSteering fluidFluid

11-37Maintenance and service– CONTINUED –use only clean fluid, and be careful not to allowany dirt into the tank. And never use differentbrands togeth

11-38Maintenance and servicetion. Recommended fluidRecommen ded Po wer steering fluid“Dexron III” Type Automatic Transmission FluidBrake fluidBrake

11-39Maintenance and service– CONTINUED –y Never splash the brake fluid over painted sur-faces or rubber parts. Alcohol contained in thebrake fluid ma

11-40Maintenance and serviceClutch fluid (MT vehicles)Clutch fluidFluid levelClutch Checking the fluid levelChecking Fluid levelNever let clutch fl

11-41Maintenance and service– CONTINUED –1) “MAX” level mark2) “MIN” level markCheck the fluid level on the outside of the reservoir. Ifthe level is b

11-42Maintenance and serviceBrake boosterBrakeBoosterIf the brake booster does not operate as described inthe following, have it checked by your SUBAR

11-43Maintenance and service– CONTINUED –tact your SUBARU dealer. Checking the brake pedal reserve dis-tanceChecking Brake pedal reserve distance

11-44Maintenance and service Checking the clutch pedal free playChecking Clutch pedal fr ee play1) 0.16 – 0.51 in (4.0 – 13.0 mm)Lightly press the

1-16Seat, seatbelt and SRS airbagsT Expectant mothersExpectant mothers also need to use the seatbelts.They should consult their doctor for specific re

11-45Maintenance and service– CONTINUED –the brake pedal is applied.If you hear this scraping noise each time you apply thebrake pedal, have the brake

11-46Maintenance and serviceParking brake strokeParkingBrake strokeCheck the parking brake stroke according to the main-tenance schedule in the “Warra

11-47Maintenance and service– CONTINUED –T Winter (snow) tiresWinter tires are best suited for driving on snow-cov-ered and icy roads. However winter

11-48Maintenance and servicevalues shown on the tire placard. The tire placard is lo-cated on the door pillar on the driver’s side.Driving even a shor

11-49Maintenance and service– CONTINUED –y Abnormally low tire pressure (tread worn atshoulders)Rolling resistance is high, so fuel consumption is als

11-50Maintenance and serviceof vehicle control could lead to an accident. Wheel balanceWheel BalanceEach wheel was correctly balanced when your veh

11-51Maintenance and service– CONTINUED –ible, the tire is worn beyond the acceptable limitand must be replaced immediately. With a tirein this condit

11-52Maintenance and serviceshown on the tire placard.Using tires of a non-specified size detracts from con-trollability, ride comfort, braking perfor

11-53Maintenance and service– CONTINUED –Aluminum wheelsAluminum wheelsAluminum wheels can be scratched and damagedeasily. Handle them carefully to ma

11-54Maintenance and servicefreeze type windshield washer fluid. SUBARU Wind-shield Washer Fluid contains 58.5% methyl alcoholand 41.5% surfactant, by

1-17Seat, seatbelt and SRS airbags– CONTINUED – Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning de-vice at the

11-55Maintenance and service– CONTINUED –Replacement of windshield wiper bladesReplacem entW indshield wiper bladesGrease, wax, insects, or other mate

11-56Maintenance and service1) Metal support3. Grasp the locked end of the blade rubber assemblyand pull it firmly until the stoppers on the rubber ar

11-57Maintenance and service– CONTINUED –5. Align the claws of the metal support with thegrooves in the rubber and slide the blade rubber as-sembly in

11-58Maintenance and serviceBatteryBatteryy Before beginning work on or near any bat-tery, be sure to extinguish all cigarettes, match-es, and lighter

11-59Maintenance and service– CONTINUED –FusesFusesNever replace a fuse with one having a higherrating or with material other than a fuse be-cause ser

11-60Maintenance and service1) Fuse puller2) Spare fusesThe fuse puller and spare fuses are stored in the mainfuse box cover in the engine compartment

11-61Maintenance and service– CONTINUED –each fuse.1) Fuse puller4. Pull out the fuse with the fuse puller.5. Inspect the fuse. If it has blown, repla

11-62Maintenance and serviceInstallation of accessoriesAccessor iesAlways consult your SUBARU dealer before installingfog lights or any other electric

11-63Maintenance and service– CONTINUED –Replacing bulbs7614235UBF047CB

11-64Maintenance and serviceWattage Bulb No.1) HeadlightBAJA-S 12V-65/55W9007 (HB5)BAJA-BLow beam 12V-55W H1High beam 12V-60W 9005 (HB3)2) Front turn

1-18Seat, seatbelt and SRS airbagsNever place the shoulder belt under the arm orbehind the back. If an accident occurs, this canincrease the risk or s

11-65Maintenance and service– CONTINUED –141213891011UBB100BB

11-66Maintenance and serviceReplace any bulb only with a new bulb of thespecified wattage. Using a bulb of differentwattage could result in a fire. H

11-67Maintenance and service– CONTINUED –T BAJA-Sport1) Electrical connector2) Push1. Disconnect the electrical connector while pressingthe lock relea

11-68Maintenance and serviceT BAJA-Turbo1) Low beam light bulb2) High beam light bulbRemove the headlight bulb cover, by turning it coun-terclockwise.

11-69Maintenance and service– CONTINUED –T Low beam light bulbs01) Electrical connector2) Red cable3) Black cable1. Disconnect the electrical connecto

11-70Maintenance and serviceT High beam light bulbs01) Push1. Disconnect the electrical connector from the bulb.2. Remove the bulb from the headlight

11-71Maintenance and service– CONTINUED –SUBARU dealer replace the bulbs if necessary. Front turn signal light, parking light and side marker lightR

11-72Maintenance and service4. Remove the bulb from the socket by pushing it andturning counterclockwise. Install a new bulb in thesocket.5. Set the b

11-73Maintenance and service– CONTINUED –3. Remove the rear combination light mounting bolts.Then, slide the rear combination light assembly to therea

11-74Maintenance and service Tail light (on the tailgate)Replacing bulb s Tail light Ta il light1. Open the tailgate.2. Remove the tailgate trim b

1-19Seat, seatbelt and SRS airbags– CONTINUED –5. To make the lap part tight, pull up on the shoulderbelt.6. Place the lap belt as low as possible on

11-75Maintenance and service– CONTINUED –4. Remove the bulb socket from the tail light by turn-ing it counterclockwise.5. Remove the bulb from the soc

11-76Maintenance and service License plate lightLicense p late ligh t Replacing bulb s Licen se plate l ight01. Push two release buttons and pull

11-77Maintenance and service– CONTINUED –4. Remove the screw from the side of the cover.5. Remove the cover.6. Remove the bulb socket from the license

11-78Maintenance and service Map light, dome light and door step lightReplacing bulb s Dome lig ht Dome light Re placing bulbs Map lightMap ligh

11-79Maintenance and service– CONTINUED –Door step light1. Remove the lens by prying the edge of the lens witha flat-head screwdriver.2. Pull the bulb

11-80Maintenance and service1) Cargo lights2) High mount stop lights2. Remove the bulb socket from the light assembly byturning it counterclockwise.3.

11-81Maintenance and service– CONTINUED – Sport activity lights (if equipped)Sport activity lights1. Remove front lamp screw and remove the lens and

12-112SpecificationsSpecifications ... 12-2Dimensions ...

12-2SpecificationsSpecificationsSpecificationsThese specifications are subject to change without notice. Dimensionsin (mm) EngineModel BAJA-Sport BA

1-20Seat, seatbelt and SRS airbagsWhen wearing the seatbelts, make sure theshoulder portion of the webbing does not passover your neck. If it does, ad

12-3Specifications– CONTINUED – Electrical system CapacitiesBattery type and capacity (5HR) MT 55D23L (12-48AH)AT 75D23L (12-52AH)Alternator 12V-90A

12-4Specifications Tires Wheel alignmentType Steel belted radial, TubelessTire size P225/60R16 97HWheel size 16 × 61/2JJPressure Front 33 psi (230 k

12-5Specifications– CONTINUED –Fuses and circuits Fuse panel located behind the coin tray1918171620151412111098765432113UBC001BBFuse panel Fuse ratin

12-6Specifications Fuse panel located in the engine com-partmentA) FWD socketB) Main fuse12 10A y Illumination brightness control13 15A y Fuel pump14

12-7Specifications– CONTINUED –Fuse panel Fuse rating Circuit1 20A (Non-tur-bo)y Radiator cooling fan (Main)30A (Turbo)2 20A (Non-tur-bo)y Radiator co

12-8SpecificationsBulb chartDescription Wattage Bulb No.HeadlightS models 12V-65/55W 9007 (HB5)Except S modelsLow beam 12V-55W H1High beam 12V-60W 900

12-9Specifications– CONTINUED –Vehicle identification216543C001131) Emission control label2) Vehicle identification number3) Tire inflation pressure l

13-113Consumer information and Reporting safety defectsTire information ... 13-2Tire labeling ...

13-2Consumer information and Reporting safety defectsConsumer inf ormation and Re porting safety de fectsFor U.S.A.The following information has been

1-21Seat, seatbelt and SRS airbags– CONTINUED –4. To make the lap part tight, pull up on the shoulderbelt.5. Place the lap belt as low as possible on

13-3Consumer information and Reporting safety defects– CONTINUED –Example:(6) Load Index: A numerical code which speci-fies the maximum load a tire ca

13-4Consumer information and Reporting safety defects(2) Tire Size(3) Tire Type Code(4) Date of ManufactureThe first two figures identify the week, st

13-5Consumer information and Reporting safety defects– CONTINUED – Recommended tire inflation pressureT Recommended cold tire inflation pressureRecom

13-6Consumer information and Reporting safety defectsExample:The vehicle placard shows original tire size, rec-ommended cold tire inflation pressure o

13-7Consumer information and Reporting safety defects– CONTINUED –The maximum cold inflation pressure to which atire may be inflated.y Recommended inf

13-8Consumer information and Reporting safety defectsdistributing to each axle its share of the curbweight, accessory weight, and normal occupantweigh

13-9Consumer information and Reporting safety defects– CONTINUED –the tongue load of a trailer. Therefore cargo ca-pacity can be calculated by the fol

13-10Consumer information and Reporting safety defects2. Calculate the available load capacity by sub-tracting the total weight from the vehicle capac

13-11Consumer information and Reporting safety defects– CONTINUED –2. Calculate the available load capacity.3. The total weight now exceeds the capaci

13-12Consumer information and Reporting safety defectsthe trailer tongue (i.e. Tongue load = 176 lbs (80kg)).1. Calculate the total weight.2. Calculat

1-22Seat, seatbelt and SRS airbagschanges that will prevent the seatbelt from op-erating properly.To clean the seatbelts, use a mild soap and lukewarm

13-13Consumer information and Reporting safety defects– CONTINUED –2. Calculate the available load capacity.3. The total weight now exceeds the capaci

13-14Consumer information and Reporting safety defects Adverse safety consequences of over-loading on handling and stopping and on tiresOverloading c

13-15Consumer information and Reporting safety defects– CONTINUED –Uniform tire quality grading stan-dardsThis information indicates the relative perf

13-16Consumer information and Reporting safety defectstests, and does not include acceleration,cornering, hydroplaning, or peak tractioncharacteristic

13-17Consumer information and Reporting safety defects– CONTINUED –Reporting safety defects (USA)If you believe that your vehicle has a defectwhich co

14-114Index

14-2IndexAABS (Anti-lock Brake System) ... 7-33Warning light ... 3-14Accessori

14-3IndexCargoBed ... 6-16Lamp ...

14-4IndexDifferential gear oilFront ... 11-32Rear ...

1-23Seat, seatbelt and SRS airbags– CONTINUED –extender.y Do not use the extender if the buckle of theextender rests over the abdomen.y Do not let som

14-5IndexGauge ... 3-8Requirements ... 7-2Fuse

14-6IndexLSD (Limited slip differential) ... 7-30MMain fuse ... 11-6

14-7IndexRear seatFolding down ... 1-10Rear windowDefogger button ...

14-8IndexSpecifications ... 12-2Speedometer ...

14-9IndexVValet mode ... 2-21Vanity mirror ...

109876543111213HSF028AA

GAS STATION REFERENCEFuel:T Non-turbo modelsUse only unleaded gasoline with an octane rat-ing of 87 AKI or higher.T Turbo modelsUse premium unleaded g

1-24Seat, seatbelt and SRS airbagsFront seatbelt pretensionersThe driver’s and front passenger’s seatbelts have aseatbelt pretensioner. The seatbelt p

2How to use this owner’s manual Using your Owner’s manualBefore you operate your vehicle, carefully read thismanual. To protect yourself and extend t

1-25Seat, seatbelt and SRS airbags– CONTINUED –y If the front seatbelt retractor assembly or sur-rounding area has been damaged, contact yourSUBARU de

1-26Seat, seatbelt and SRS airbagswhen the ignition switch is turned to the “ON” position.The following components are monitored by the indi-cator: y

1-27Seat, seatbelt and SRS airbags– CONTINUED –The front sub sensors are located in both frontfenders and the airbag control module includ-ing the imp

1-28Seat, seatbelt and SRS airbagsChild restraint systemsInfants and small children should always be placed inan infant or child restraint system in t

1-29Seat, seatbelt and SRS airbags– CONTINUED –Never let a passenger hold a child on his or herlap while the vehicle is moving. The passengercannot pr

1-30Seat, seatbelt and SRS airbagsA: Front passenger’s seatYou should not install a child restraint system (includ-ing a booster seat) due to the haza

1-31Seat, seatbelt and SRS airbags– CONTINUED –SINCE YOUR VEHICLE IS EQUIPPED WITH APASSENGER’S SRS AIRBAG, DO NOT IN-STALL A REARWARD FACING CHILD SA

1-32Seat, seatbelt and SRS airbags Installing child restraint systems with A/ELR seatbelty Child restraint systems and seatbelts can be-come hot in a

1-33Seat, seatbelt and SRS airbags– CONTINUED –4. Take up the slack in the lap belt.5. Pull out the seatbelt fully from the retractor tochange the ret

1-34Seat, seatbelt and SRS airbags8. To remove the child restraint system, press the re-lease button on the seatbelt buckle and allow the beltto retra

3– CONTINUED –Chapter 13: Consumer information and Reportingsafety defectsThis chapter informs you about Tire information, Uni-form tire quality gradi

1-35Seat, seatbelt and SRS airbags– CONTINUED –position. If it is not held tight and secure, thedanger of your child suffering personal injury inthe e

1-36Seat, seatbelt and SRS airbags3. Connect the tether belt hook onto the tether an-chorage on the backside of the seatback. Take up anyslack in the

1-37Seat, seatbelt and SRS airbags– CONTINUED –7. Insert the tongue plate into the buckle.8. Take up the slack in the lap belt.9. Pull out the seatbel

1-38Seat, seatbelt and SRS airbags11.While pushing the child restraint into the seat cush-ion and moving it back and forth, pull the upper tetherbelt

1-39Seat, seatbelt and SRS airbags– CONTINUED –3. Insert the tongue plate into the buckle.4. Take up the slack in the lap belt.5. Pull out the seatbel

1-40Seat, seatbelt and SRS airbags8. To remove the child restraint system, press the re-lease button on the seatbelt buckle and allow the beltto retra

1-41Seat, seatbelt and SRS airbags– CONTINUED –Some types of child restraint systems can be installedon the rear seat of your vehicle without use of t

1-42Seat, seatbelt and SRS airbagsEach lower anchorage is located where the seat cush-ion meets the seatback.1. Place the child restraint system on th

1-43Seat, seatbelt and SRS airbags– CONTINUED –3. Connect the hook of the upper tether belt onto thetether anchorage on the backside of the seatback.

1-44Seat, seatbelt and SRS airbags6. While following the instructions supplied by thechild restraint system manufacturer, connect the lowerhooks onto

4ual. This symbol means “Do not”, “Do not do this”, or“Do not let this happen”, depending upon the context.Safety precautions when driving Seatbelt a

1-45Seat, seatbelt and SRS airbags– CONTINUED –8. Pull the upper tether belt straight up to secure thechild restraint system firmly by taking up the s

1-46Seat, seatbelt and SRS airbagsthe event of an accident may be increased.1. Place the booster seat in the rear seating positionand sit the child on

1-47Seat, seatbelt and SRS airbags– CONTINUED –effective in preventing or reducing injury.y Place the lap belt as low as possible on thechild’s hips.

1-48Seat, seatbelt and SRS airbagsy To obtain maximum protection in the event ofan accident, the driver and all passengers in thevehicle should always

1-49Seat, seatbelt and SRS airbags– CONTINUED –Put children aged 12 and under in the rear seatproperly restrained at all times. The SRS airbagdeploys

1-50Seat, seatbelt and SRS airbagsy When the SRS airbag deploys, some smokewill be released. This smoke could causebreathing problems for people with

1-51Seat, seatbelt and SRS airbags– CONTINUED –T Components2143576UB1135BB1) Airbag control module (including impact sensors)2) Airbag module (driver’

1-52Seat, seatbelt and SRS airbags SRS frontal airbagThe driver’s SRS frontal airbag is stowed in the centerportion of the steering wheel. The passen

1-53Seat, seatbelt and SRS airbags– CONTINUED –Never hold a child on your lap or in your arms.The SRS airbag deploys with considerableforce and can in

1-54Seat, seatbelt and SRS airbagsavoid injuries that can result when the SRS air-bag contacts an occupant not in proper posi-tion such as one thrown

5– CONTINUED –ment, the driver should always sit upright andwell back in the seat as far from the steeringwheel as practical while still maintaining f

1-55Seat, seatbelt and SRS airbags– CONTINUED –T OperationA) Driver’s sideB) Passenger’s side1) SRS airbags deploy as soon as a collision occurs.2) Af

1-56Seat, seatbelt and SRS airbagsThe SRS airbag can function only when the ignitionswitch is in the “ON” position.If the front sub sensors inside the

1-57Seat, seatbelt and SRS airbags– CONTINUED –experienced in the passenger compartment during acollision. That level differs from one type of collisi

1-58Seat, seatbelt and SRS airbagsThe SRS frontal airbag may be activated when the ve-hicle sustains a hard impact in the undercarriage areafrom the r

1-59Seat, seatbelt and SRS airbags– CONTINUED –or sign pole, or if it slides under a truck’s load bed, orif it sustains an oblique offset frontal impa

1-60Seat, seatbelt and SRS airbagsin a low-speed frontal collision.1) First impact!2) Second impact!!In an accident where the vehicle is impacted more

1-61Seat, seatbelt and SRS airbags– CONTINUED –y Front sub sensor (Left-hand side)y Airbag control module (including impact sensors)y Frontal airbag m

1-62Seat, seatbelt and SRS airbagsthe following, have an authorized SUBARUdealer perform the work. The SRS airbag con-trol module, impact sensors and

1-63Seat, seatbelt and SRS airbags– CONTINUED –Do not perform any of the following modifica-tions. Such modifications can interfere withproper operati

6the lock switch when children are riding in thevehicle. Failure to follow this procedure couldresult in injury to a child operating the powerwindow.

2-12Keys and doorsKeys ... 2-2Key number ...

2-2Keys and doorsKeys and doorsKeysKeys1) Master key2) Submaster key3) Valet key4) Key number plateThree types of keys are provided for your vehicle.M

2-3Keys and doors– CONTINUED –Door locksDoor locks Locking and unlocking from the out-sideTo lock the driver’s door from the outside with the key,ins

2-4Keys and doorsLocking without the key1) Push the power door locking switch forward.2) Close the door.To lock the door from the outside without the

2-5Keys and doors– CONTINUED –1) Lock2) UnlockTo lock the door from the inside, rotate the lock leverrearward. To unlock the door from the inside, rot

2-6Keys and doorsFront passenger’s switch1) Lock2) UnlockAll doors can be locked and unlocked by the powerdoor locking switches located at the driver’

2-7Keys and doors– CONTINUED –Remote keyless entry systemRemote ke yless entry systemTwo transmitters are provided for your vehicle.The remote keyless

2-8Keys and doors: LOCK/ARM buttonPress to Lock all doors. Press and Hold to activate panic alarm.Press three times in a five-second period to use veh

2-9Keys and doors– CONTINUED – Illuminated entryIlluminated ent ryThe interior dome light and ignition switch light will illu-minate when the “ ” bu

2-10Keys and doorspower door locking switch, close the driver’s dooronce within 10 seconds after Step 4.6. The turn signal lights flashes 3 times to i